Edmond Water Heater Repair
Steam rising from a hot shower in a bright bathroom (illustrative photo)

No Hot Water? Water Heater Checks for Edmond Homes

Ice-cold shower in Edmond this morning? Run the short checks below, or call or text and you'll get a call right back with a price first.

Updated Prices checked

  • Gas, electric and tankless models
  • Phone answered day and night
  • National average repair $200–$850

Water heater trouble?

Water heater trouble? Tell me what's going on, and I'll get right back to you.

* required

!Please enter your name.
!Please enter a 10-digit phone number.

Answered 24/7. Rather talk? Call or text (405) 562-5258.

Before opening a single panel, rule out the simplest cause: the whole house has no power or no gas. A dead clock on the microwave, or a stove that will not light, means the problem is upstream of the heater.

Is my water heater gas or electric?

You can tell by looking at the top and base of the tank. A metal flue pipe on top and a gas line with a control dial near the floor mean gas, while a thick cable into the side and no flue mean electric.

  • Gas tank: a small window near the base shows the pilot or burner, and the label says natural gas or propane.
  • Electric tank: square access panels on the side hide the thermostats and heating elements.
  • Tankless: a wall-mounted box. A gas model has a vent pipe leading outdoors.

In Edmond, Oklahoma Natural Gas supplies natural gas, and Edmond Electric, the city-owned utility, serves homes inside the city. That is not true of every address with an Edmond mailing address, so your own bill is the final word on which utility you have.

Did a storm or an outage cause this?

An outage is a common reason for cold water on an electric heater, and Edmond has plenty of weather to cause one. Edmond Electric says tornadoes, ice storms and straight-line winds bring its larger outages, and an electric tank cannot heat while the power is off.

When power returns, give the heater a few hours to recover before assuming it is broken. If the house has power and the heater still stays cold, a surge may have tripped the breaker or the heater's own safety switch. A gas heater with an electronic igniter can also fail to light during an outage, so the next section applies to it as well.

My electric heater has no hot water. What do I check?

An electric heater with no hot water should be checked at the breaker, then at the red reset button behind the upper access panel. A tripped breaker or a tripped high-limit switch is the most common cause.

  1. Find the double breaker marked water heater. If it sits between on and off, push it fully off, then fully on. If it trips again at once, stop there.
  2. Turn the breaker off, remove the upper panel, fold back the insulation and press the red button until it clicks.
  3. Close everything up, switch the breaker on, and give the tank about an hour.
  4. Run a hot tap. If the water is warm, the heater is back; if it is cold again later, the cause is still there.

A reset button that trips repeatedly is the heater telling you something is wrong. Do not keep pressing it. That is a repair visit, not a do-it-yourself job.

My gas heater has no hot water. What do I check?

A gas heater with no hot water most often has a pilot that went out or a thermocouple that no longer senses the flame. The label on the tank carries the lighting instructions for your exact model.

  • Standing pilot: if the flame will light but dies when you release the knob, the thermocouple is the likely failure.
  • Electronic igniter: newer models blink a status light instead of showing a pilot, and the label explains the code.
  • Gas valve: confirm the valve on the supply line is open and another gas appliance, such as the stove, works.

Smell gas? Stop. Get everyone outside, call 911, then call the Oklahoma Natural Gas leak line at 800-458-4251 from a safe distance. Touch no switches and do not use a phone inside.

Pilot will not stay lit? Call or text, and a price comes first.

(405) 562-5258Talk to a plumber 24/7Text Us

Why is the water only lukewarm, or hot for a few minutes?

Hot water that fades quickly or never gets truly hot usually means the heater is working but producing less than it should. Three causes cover most cases.

  • Failed lower element: on an electric tank, the upper element heats a small top layer, so you get a short burst of hot water and then a cold stretch.
  • Broken dip tube: it carries incoming water to the bottom, and when it cracks, cold water mixes in at the top. Tiny white plastic bits in faucet screens are the clue.
  • Sediment: the City of Edmond calls its water hard, and hardness varies by address because the supply mixes lake, well and purchased Oklahoma City water. Minerals settle at the bottom of the tank and take up room that should hold hot water.

What if a tankless heater has no hot water?

A tankless heater with no hot water usually fails to fire because of low flow, scale or a fuel or power fault, and the display typically shows a code that narrows it down. The owner's manual translates each code.

  • Low flow: a tankless unit only ignites above a minimum flow, so a trickle at one tap may never turn it on.
  • Scale: minerals narrow the heat exchanger's passages. Manufacturers call for descaling at least yearly, and hard water makes that more important.
  • Gas or power: check the breaker, and on a gas unit confirm the supply valve is open.

When should I stop and call?

Stop when a breaker trips twice, when the pilot refuses to stay lit after a careful relight, when you see water on the floor, or when the next step means opening wiring or a gas valve. Those are jobs for a licensed plumber.

  • Repeat trips: something is shorted or overheating.
  • Water on the floor: go to the leaking water heater guide and shut the water off first.
  • Any gas smell: leave first, then call.

What do the common fixes cost?

Across the country a repair visit for a heater with no hot water averages $200 to $850, about $550 in the middle, and the parts involved mostly sit at the low end.

RepairTypical rangeNotes
Thermostat$125–$275electric
Heating element$150–$325electric
Thermocouple$125–$250gas, pilot will not stay lit
Pilot light or igniter$50–$175gas
Gas control valve$250–$450gas
Dip tube$60–$240lukewarm water
Tank flush$100–$225sediment
Tankless descale$110–$275scale in the exchanger

You will get a price for your exact repair before any work starts. Ask whoever does the job whether they are licensed, and the Oklahoma Construction Industries Board has a public lookup if you want to check. See water heater repair for what a visit covers.

Repair prices here are rounded averages of several national cost guides; the pricing page lists how they were figured.

Is it time for a replacement instead?

An older tank often makes replacement the better buy, since a tank typically lasts 8 to 15 years and a thermostat today can be followed by an element next month. One small part on a tank that is not leaking can still be worth fixing.

Read the build date on the tank's label, which is sometimes folded into the serial number. A tank that is old and also rusty, noisy or damp underneath is worth asking about replacement on the same callback, so you can weigh both prices before any work starts. The replacement cost guide has the ranges, or get your quote now.

Back to hot showers sooner: call or text, and a price comes before any work.

(405) 562-5258Talk to a plumber 24/7Text Us

Questions homeowners ask

Why did my electric water heater go cold after a storm?

A storm outage or a surge can trip the breaker or the red reset button on the heater. Check the breaker first, then the reset button behind the upper panel. If either trips again right away, stop and call, because that points to a shorted element or wiring.

Will relighting the pilot fix a gas water heater with no hot water?

It will when the pilot simply blew out, and the steps are printed on the heater's label. If the flame will not stay lit after a couple of careful tries, the thermocouple or gas control is the likely culprit and the next step is a repair.

Why is my hot water lukewarm instead of cold?

Lukewarm usually means a failed lower element, a broken dip tube or a tank crowded with sediment. The heater is running, but it is producing less hot water than the house wants.

Who do I call if the whole house lost power?

For homes served by Edmond Electric, the outage line is 405-216-7660, and a downed wire is a 911 call. Not everyone with an Edmond address is on Edmond Electric, so check your bill for the name of your electric provider.

How much does it cost to fix a heater that has no hot water?

National averages put a repair visit for no hot water at $200 to $850, about $550 in the middle, and common parts such as a thermostat, element or thermocouple at $125 to $325.

Last updated:

Text Edmond Water Heater Repair

Tell me what's going on with your water heater, and I'll get right back to you.

* required

!Please enter your name.
!Please enter a 10-digit phone number.

Rather talk? Call or text (405) 562-5258.